question-circle Question looking for pinning internal 26-pole header...

  • Jodocus
  • Jodocus's Avatar Topic Author
  • Offline
  • Forum Nutzer
  • Forum Nutzer
More
24 Feb 2017 00:18 #44801 by Jodocus
Hi,

I'm looking for the internal pinning of the Stepcraft. I think I saw a schematic somewhere on the forum, but I'm not able to find it.

Basically what I have found so far is:

1 Spindle on/off OUTPUT
2 DIR X
3 STEP X
4 DIR Y
5 STEP Y
6 DIR Z
7 STEP Z
8 DIR A
9 STEP A
10 Toollength sensor INPUT
11 Emergency stop INPUT
12 HOME X/Y/Z INPUT
13 HOME A INPUY
14 COOLANT OUTPUT
15 ?
16 ?
17 ?
18 GROUND
19 GROUND
20 GROUND
21 GROUND
22 GROUND
23 GROUND
24 GROUND
25 GROUND
26 +5V ?

I hope someone can fill in the gaps and/or confirm the signals please ?

Thanks in advance

Please Log in or Create an account to join the conversation.

  • MagIO2
  • MagIO2's Avatar
  • Offline
  • Forum Nutzer
  • Forum Nutzer
  • Zu viele Ideen und zu wenig Zeit
More
24 Feb 2017 06:41 #44804 by MagIO2
Guess your labels are from PC point of view and not from SC header point of view, otherwise I and O are swapped.

SC Machine parameters

SC 420 mit DIY parallel + Proxxon mit Mod + HF500 + SprintLayout + LibreCAD/QCAD + FreeCAD +WinPC starter/USB->EstlCAM + EstlCAM LPTAdapter + EstlCAM Handrad + DIY Vakuumtisch

Gruß, Andreas

Please Log in or Create an account to join the conversation.

  • Jodocus
  • Jodocus's Avatar Topic Author
  • Offline
  • Forum Nutzer
  • Forum Nutzer
More
24 Feb 2017 11:37 #44819 by Jodocus
Hi,

Uhh, I think your right :P

I'll will double check, but do you perhaps know whether the signals are correct and/or what the missing signals are ?

Please Log in or Create an account to join the conversation.

More
24 Feb 2017 12:37 #44822 by Rahul

Jodocus wrote: Hi,

Uhh, I think your right :P

I'll will double check, but do you perhaps know whether the signals are correct and/or what the missing signals are ?


Pin 17 (PWM) is used by the HF-Spindle to control the rpm (in my opinion).

You should look for the Arduino Shield in this forum there could be more information.

Fräse: SC 2/840 USB, Proxxon IBS/E STEPCRAFT HF-500, Werkzeugwechsler + WZLS + T-Nutentisch
3D-Drucker: MendelMax 1.5
CAD: Designspark Mechanical, Eagle
CAM: Estlcam V9, DeskProto

Please Log in or Create an account to join the conversation.

  • Jodocus
  • Jodocus's Avatar Topic Author
  • Offline
  • Forum Nutzer
  • Forum Nutzer
More
25 Feb 2017 00:07 #44873 by Jodocus
Hi,

Thanks, I'll look. I'm sure I saw somewhere in a thread more info... Should have marked it :S

Please Log in or Create an account to join the conversation.

  • MagIO2
  • MagIO2's Avatar
  • Offline
  • Forum Nutzer
  • Forum Nutzer
  • Zu viele Ideen und zu wenig Zeit
More
25 Feb 2017 00:32 - 25 Feb 2017 00:36 #44874 by MagIO2
You understand that the words written in orange are a link to a PDF listing the Pinout on page 2, first table?

SC 420 mit DIY parallel + Proxxon mit Mod + HF500 + SprintLayout + LibreCAD/QCAD + FreeCAD +WinPC starter/USB->EstlCAM + EstlCAM LPTAdapter + EstlCAM Handrad + DIY Vakuumtisch

Gruß, Andreas
Last edit: 25 Feb 2017 00:36 by MagIO2.
The following user(s) said Thank You: Jodocus

Please Log in or Create an account to join the conversation.

Powered by Kunena Forum

© 2022 STEPCRAFT GmbH & Co. KG

We use cookies

We use cookies on our website. Some of them are essential for the operation of the site, while others help us to improve this site and the user experience (tracking cookies). You can decide for yourself whether you want to allow cookies or not. Please note that if you reject them, you may not be able to use all the functionalities of the site.