file Frage 3D printing with Mach3 STEP BY STEP

Mehr
20 Mai 2015 09:49 #20971 von Worldhusky
Worldhusky antwortete auf 3D printing with Mach3 STEP BY STEP

Rory schrieb: ... (can't upload them to here for some reason)... send us an email.

Try as a *.zip - should work. ;)

It's not only about tools it's also about skills! ;)

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
20 Mai 2015 20:53 #21013 von dtomee
dtomee antwortete auf 3D printing with Mach3 STEP BY STEP
Rory thanks for you help. Unfortunately, i'd already used your configuration (only with the change of the port with Ox378). In this case there are no action when i'm pressing A+ button.

Another question : when i would like to change the temperature, directly on the control print boxe, nothing. The temperature is fixed around 207°C; Is it normal ?

I suspect a manufacturing defect. My configuration is only a lpt1 connection between MACH3 and the stepcraft, no 4th axis card. I understood that it was'nt necessary.

If somebody have an idea,

Many thanks in advance

David

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
22 Mai 2015 20:44 #21145 von dtomee
dtomee antwortete auf 3D printing with Mach3 STEP BY STEP
Hello,

I resolved my problem. The stepcraft works fine now (milling+ 3dprinter).

Two wholes:

The temperature must be adjusted first, turn off the controler, and restart

Adjust the frequency at 100khz.

The PLA's flow is very slow. If you want to see the flow adjust the manuel jog´s speed to 100%.

David

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
01 Jun 2015 11:40 - 01 Jun 2015 11:42 #21794 von dtomee
dtomee antwortete auf 3D printing with Mach3 STEP BY STEP
Finally, i'm somewhat disillusioned with the 3D printer. The 4th axe doesn't run; the PLA's flow observed came from only the internal pressure and stop after only few minutes.

The stepper motor did'nt receive instruction from MACH3.

I've contacted Stepcraft for the guarantee.

Wait and See...

A question for Rory:

I didn't understand our Macro M107. The followings instructions in the macro, don't seem to match up with 4th axe ?

doOemButton(1011)
Code "G00 X0 Y0"
While IsMoving()
Wend

David
Letzte Änderung: 01 Jun 2015 11:42 von dtomee.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
01 Jun 2015 17:52 #21798 von carbon
carbon antwortete auf 3D printing with Mach3 STEP BY STEP
Trying to use my recently built SC600 to 3D print. The problem I am having is that the material (PLA) seems to be feeding too quickly and interfering with the nozzle on its next pass, which then wipes out the structure. Is there a way in QuickNCPC to slow down the filament feed rate? I have tried the 4th axis speed settings but nothing seems to affect it. Any help will be appreciated.

Thanks,

Gary

SC 600. WinPCNC Pro/UNC, 3D Printhead, Aluminum Bed, Foam Cutter, Engraver

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
01 Jun 2015 22:22 #21809 von carbon
carbon antwortete auf 3D printing with Mach3 STEP BY STEP
I think I figured the problem out. I had scaled the model by 0.5 in x, y, and z to reduce its print size. It seems that this doesn't also reduce the feed rate to the extruder in QuickNCPC. Can anybody verify this for me? It is printing fine at the drawn size of the STL.

Thanks,
Gary

SC 600. WinPCNC Pro/UNC, 3D Printhead, Aluminum Bed, Foam Cutter, Engraver

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
04 Jun 2015 10:49 #21873 von Rory

carbon schrieb: Trying to use my recently built SC600 to 3D print. The problem I am having is that the material (PLA) seems to be feeding too quickly and interfering with the nozzle on its next pass, which then wipes out the structure. Is there a way in QuickNCPC to slow down the filament feed rate? I have tried the 4th axis speed settings but nothing seems to affect it. Any help will be appreciated.

Thanks,

Gary


One way is to tune the "steps per unit" on the A axis - so you have the same Gcode and the motor moves a little less. This will need some testing / teaking.

Not sure can you change the displacement of the 4th axis code from repetier. the 4th axis is programmed with a G01 command.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
04 Jun 2015 10:52 #21874 von Rory

dtomee schrieb: Finally, i'm somewhat disillusioned with the 3D printer. The 4th axe doesn't run; the PLA's flow observed came from only the internal pressure and stop after only few minutes.

The stepper motor did'nt receive instruction from MACH3.

I've contacted Stepcraft for the guarantee.

Wait and See...

A question for Rory:

I didn't understand our Macro M107. The followings instructions in the macro, don't seem to match up with 4th axe ?

doOemButton(1011)
Code "G00 X0 Y0"
While IsMoving()
Wend

David


DoOEMButton(1011) zeros the A axis so it won't spool in reverse when start again and go back to zero. It then moves to the XY 00 position.


You need to make sure your A axis mach3 profile has step pin 9 and dir pin 8 on port 1 for the A axis.

The connector between the SC card and the 3D printer is all thats needed - no need for the 4th axis card.

most likely its your settings in Mach3.
Folgende Benutzer bedankten sich: dtomee, Ktshung

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
04 Jun 2015 11:15 #21876 von dtomee
dtomee antwortete auf 3D printing with Mach3 STEP BY STEP
Yes, the pin connections are good. There is one more thing that think me about failure: the temperature doesn't

stabilize around the setpoint temperature. For example i fixed 170°C, and the temperature increased and stop around 186 °C;

I've contacted Stepcraft support and i'll prepare a return of the print head for diagnostic. i'will cost me 50 euros and it gives me no pleasure.

Rory thank you very much for your Help.

David

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
30 Nov 2015 10:47 #27659 von MikeRD03
MikeRD03 antwortete auf 3D printing with Mach3 STEP BY STEP
I tried to make the cooler work with Mach3. I use KISSSlicer for slicing and would need the correct Mach3 config for controlling the cooler und the commands for switching on/off and controlling the speed. Can anyone help?

SC M.500 | 2,2kW Spindel G-Penny | Mach4 über Ethernet Smoothstepper

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
31 Mär 2016 23:28 #32687 von osamaie
osamaie antwortete auf 3D printing with Mach3 STEP BY STEP
Dear, Rory

Could you please, send me the macro of zero starting of A-axis
email: Diese E-Mail-Adresse ist vor Spambots geschützt! Zur Anzeige muss JavaScript eingeschaltet sein!

Thanks

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
01 Apr 2016 18:51 #32712 von osamaie
osamaie antwortete auf 3D printing with Mach3 STEP BY STEP
Dear, Rory

Thanks a lot for your support

I received your email

Thanks

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
28 Apr 2016 16:31 #33662 von Ktshung
Ktshung antwortete auf 3D printing with Mach3 STEP BY STEP
Dear Rosy
Could you please send to me the macro of zero starting of A-axis too.
My email : Diese E-Mail-Adresse ist vor Spambots geschützt! Zur Anzeige muss JavaScript eingeschaltet sein!. Thank you for your help

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
28 Apr 2016 23:56 #33677 von Ktshung
Ktshung antwortete auf 3D printing with Mach3 STEP BY STEP

Ktshung schrieb: Dear Rory
Could you please send to me the macro of zero starting of A-axis too.
My email : Diese E-Mail-Adresse ist vor Spambots geschützt! Zur Anzeige muss JavaScript eingeschaltet sein!. Thank you for your help

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
01 Mai 2016 17:30 #33771 von Aliyye
Aliyye antwortete auf 3D printing with Mach3 STEP BY STEP
Let me try it where to find the software can some one explain what to do
thank you

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
12 Jul 2016 15:20 #35724 von Adylbekov
Adylbekov antwortete auf 3D printing with Mach3 STEP BY STEP
Hi Rory,
Great job, but there is nothing in dropbox file?

Dieser Beitrag enthält einen Bildanhang.
Bitte anmelden (oder registrieren) um ihn zu sehen.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
12 Jul 2016 15:23 #35725 von Adylbekov
Adylbekov antwortete auf 3D printing with Mach3 STEP BY STEP
Hi Rory,
Can you please email me the macro files?
Email: Diese E-Mail-Adresse ist vor Spambots geschützt! Zur Anzeige muss JavaScript eingeschaltet sein!

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
12 Jul 2016 15:35 #35726 von Adylbekov
Adylbekov antwortete auf 3D printing with Mach3 STEP BY STEP
Hi Osamaie,
Can you please send me macro files?
Thank you:)
email: Diese E-Mail-Adresse ist vor Spambots geschützt! Zur Anzeige muss JavaScript eingeschaltet sein!

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
15 Sep 2016 19:42 #37461 von [email protected]
Hi Rory,
Can you please email me the macro M107 & M109 files?
Email: Diese E-Mail-Adresse ist vor Spambots geschützt! Zur Anzeige muss JavaScript eingeschaltet sein!

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
10 Nov 2016 06:04 #39285 von ateeqspear
ateeqspear antwortete auf 3D printing with Mach3 STEP BY STEP
Hi Sir
We are going to design a 3D printer using mach3 and we need Stepcraft 3D print extension file file. Waiting for your reply.
Thank you

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Powered by Kunena Forum

© 2022 STEPCRAFT GmbH & Co. KG

Wir benutzen Cookies

Wir nutzen Cookies auf unserer Website. Einige von ihnen sind essenziell für den Betrieb der Seite, während andere uns helfen, diese Website und die Nutzererfahrung zu verbessern (Tracking Cookies). Sie können selbst entscheiden, ob Sie die Cookies zulassen möchten. Bitte beachten Sie, dass bei einer Ablehnung womöglich nicht mehr alle Funktionalitäten der Seite zur Verfügung stehen.