file Frage Got first run today , a little ? tho..

Mehr
11 Nov 2018 20:28 #55022 von TommyF
Got first run today , a little ? tho.. wurde erstellt von TommyF
As wrote in topic, 1 run today with brand new 420,,, got the XLM to Mach3 setup from my StepCraft dealer,,, it runs fine,,,,

XYZ manually keyboard arrows run/control, axis go all in direction they suppose to do.. and also in Mach3 RUN/gcode in Mach3...

My problem is G28 that Fusion insert in POST, IE G28 Z0,,, then the Z goes downwords into the table, in sted of up to Z homeswitch (((that should be 0 i think)))..

Fusion use G28 to raise Z to clear fixture before run in XY, ofc i can disable G28, but nice to be safe..

Any ide why :-)

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
11 Nov 2018 20:34 #55023 von RonaldMcDonald
RonaldMcDonald antwortete auf Got first run today , a little ? tho..
Your end switch for z-axis has to be set to zero. All of your working space is in negative values.

I can give you my 420 settings if you want.

BR,
Ronald

The only difference between man and boys is the price of their toys.
Fusion360, Mach3, UC100, SC 2/420, Kress 1050 FME-P, Sorotec Nutenplatte, Sorotec Vakuumtisch

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
11 Nov 2018 21:14 #55025 von TommyF
Hey

Looking on it now,, in softlimits i have..

Z: softmax=130,, softlim=0,, homeoff=130,,

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
11 Nov 2018 21:50 #55028 von RonaldMcDonald
RonaldMcDonald antwortete auf Got first run today , a little ? tho..
Right. This is possibly wrong. Try max=0mm, min=-130mm, home=0mm

BR,
Ronald

The only difference between man and boys is the price of their toys.
Fusion360, Mach3, UC100, SC 2/420, Kress 1050 FME-P, Sorotec Nutenplatte, Sorotec Vakuumtisch

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
11 Nov 2018 22:42 #55029 von TommyF
Yes, thx, do you have x and y to?

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
12 Nov 2018 08:19 #55031 von TommyF
I mess around,,, the fix on Y worked :-) Now Z goes up,,

Sadly i forgot to take a picture of the settings before i tryed other settings, and soft llilimts wont work now...

If some of you will post a picture of Mach3 Softlilimts screen would be help full :-)

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
12 Nov 2018 11:26 #55033 von TommyF
Got most work now,,, only thing is that ater job finish it goes to left front, i want it to go left back?

But if i change Home offset from 418 to 0 i get a Softlimit error.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
12 Nov 2018 20:24 #55040 von RonaldMcDonald
RonaldMcDonald antwortete auf Got first run today , a little ? tho..
This is due to the strange G28 code. I also didn´t succeed to get it to the other end. It always goes to x=0, y=0, z=0 at the end of every job. Please find attached the settings of my 420/2. If you succeed to change the G28 code in your post processor to get the machine to x=0, y=420 and z=0 at the end of every job, I would really appreciate when you could tell me how to do it.

Best regards,
Ronald

The only difference between man and boys is the price of their toys.
Fusion360, Mach3, UC100, SC 2/420, Kress 1050 FME-P, Sorotec Nutenplatte, Sorotec Vakuumtisch

Dieser Beitrag enthält einen Anhang.
Bitte anmelden (oder registrieren) um ihn zu sehen.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
12 Nov 2018 20:49 #55041 von TommyF
G28 only tell to gotot machine 0.0.0 as i know,, the strange thing for me is cant get Mach3 offset/Softlimits to accept Y=0 is left back corner :-)

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
12 Nov 2018 22:15 #55043 von RonaldMcDonald
RonaldMcDonald antwortete auf Got first run today , a little ? tho..
Oh, you´re totally right. I never thought about this problem this way, but we can also do it this way. We are totally free to choose the origin of our machine coordinate system. Actually, I have the following settings.

X-Axis: Soft Max=295.5mm, Soft Min=0mm, Home Off.=0mm
Y-Axis: Soft Max=418mm, Soft Min=0mm, Home Off.=418mm
Z-Axis: Soft Max=0mm, Soft Min=-138mm, Home Off.=0mm

If we want the machine to go to the upper left corner, when going to zero, we have to tell Mach3 that all the end switches are at zero position. In my case, the settings must be the following ones (not tested yet):

X-Axis: Soft Max=295.5mm, Soft Min=0mm, Home Off.=0mm
Y-Axis: Soft Max=0mm, Soft Min=-418mm, Home Off.=0mm
Z-Axis: Soft Max=0mm, Soft Min=-138mm, Home Off.=0mm

So you only have to set the home position for the Y-Axis and the Soft Max for the Y-Axis to zero and the Soft Min to -418mm or what ever you actually have at Soft Max.

Give it a try and let me know the results.

I will test it tomorrow.

Best regards,
Ronald

The only difference between man and boys is the price of their toys.
Fusion360, Mach3, UC100, SC 2/420, Kress 1050 FME-P, Sorotec Nutenplatte, Sorotec Vakuumtisch

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
12 Nov 2018 22:29 #55045 von TommyF
Thx i will test that :-)

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
14 Nov 2018 21:35 #55062 von RonaldMcDonald
RonaldMcDonald antwortete auf Got first run today , a little ? tho..
Did you already test it?

BR,
Ronald

The only difference between man and boys is the price of their toys.
Fusion360, Mach3, UC100, SC 2/420, Kress 1050 FME-P, Sorotec Nutenplatte, Sorotec Vakuumtisch

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
16 Nov 2018 12:04 #55099 von TommyF
Hello,, no not yet, havend had the machine started yet, had a busy week :-)

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
16 Nov 2018 19:44 #55109 von TommyF
So i testet some...

X= max=299,0,,,,,Min=0,0,,,,,,,Off=0,0
y= max=418,0,,,,,Min=0,0,,,,,,,Off=418,0
X= max=130,0,,,,,Min=0,0,,,,,,,Off=130,0

Homing and soft endstop and slowdown zone works great..

If i put in G28=0 it goes down to the bed..

If i reverse Y ---Max=0,0 Min=-130 Off=130 then G28=0 works, it goes up
But then Softlimits give me warning and wont run..

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
16 Nov 2018 19:57 #55111 von RonaldMcDonald
RonaldMcDonald antwortete auf Got first run today , a little ? tho..
You don't want the machine to go down after a job. That's dangerous for workpiece and mill.
If you want the machine to go to the upper left corner in the back all home switches must be zero.

Try the following settings.

X= max=299,0,,,,,Min=0,0,,,,,,,Off=0,0
y= max=0,,,,,Min=-418,,,,,,,Off=0
Z= max=0,,,,,Min=-130,,,,,,,Off=0

BR,
Ronald

The only difference between man and boys is the price of their toys.
Fusion360, Mach3, UC100, SC 2/420, Kress 1050 FME-P, Sorotec Nutenplatte, Sorotec Vakuumtisch

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
16 Nov 2018 20:04 - 16 Nov 2018 20:05 #55112 von RonaldMcDonald
RonaldMcDonald antwortete auf Got first run today , a little ? tho..
Here is a screenshot.

Home position for x-axis has to be negative.


The only difference between man and boys is the price of their toys.
Fusion360, Mach3, UC100, SC 2/420, Kress 1050 FME-P, Sorotec Nutenplatte, Sorotec Vakuumtisch

Dieser Beitrag enthält einen Bildanhang.
Bitte anmelden (oder registrieren) um ihn zu sehen.

Letzte Änderung: 16 Nov 2018 20:05 von RonaldMcDonald.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
16 Nov 2018 20:29 #55113 von RonaldMcDonald
RonaldMcDonald antwortete auf Got first run today , a little ? tho..
Hey, Tommy.

Please find attached my working config. I have been in the workshop for short to test the settings. What shall I say. These settings work like a charm. Reference position is the upper left corner at the backside of the machine. The soft limits are perfectly fitting the working area of my machine and after every job the machine goes to x=0, y=0, z=0 at the upper left corner at the back.

Best regards,
Ronald


The only difference between man and boys is the price of their toys.
Fusion360, Mach3, UC100, SC 2/420, Kress 1050 FME-P, Sorotec Nutenplatte, Sorotec Vakuumtisch

Dieser Beitrag enthält einen Bildanhang.
Bitte anmelden (oder registrieren) um ihn zu sehen.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
17 Nov 2018 00:03 #55125 von TommyF
Mann how many time i have lost my post to timeout here...

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
17 Nov 2018 17:17 #55134 von TommyF
Got it to work with Z max=0 Min=-130 off=0.. :-) Thx

Only funny thing, if i manually run axis the slowdown in near end works fine,, but with the G28 it do not slow down near the end,,, it do stop tho, but no slowdown in Mach3.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
18 Nov 2018 14:06 - 18 Nov 2018 14:06 #55141 von RonaldMcDonald
RonaldMcDonald antwortete auf Got first run today , a little ? tho..
Perfect!

The only difference between man and boys is the price of their toys.
Fusion360, Mach3, UC100, SC 2/420, Kress 1050 FME-P, Sorotec Nutenplatte, Sorotec Vakuumtisch
Letzte Änderung: 18 Nov 2018 14:06 von RonaldMcDonald.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Powered by Kunena Forum

© 2022 STEPCRAFT GmbH & Co. KG

Wir benutzen Cookies

Wir nutzen Cookies auf unserer Website. Einige von ihnen sind essenziell für den Betrieb der Seite, während andere uns helfen, diese Website und die Nutzererfahrung zu verbessern (Tracking Cookies). Sie können selbst entscheiden, ob Sie die Cookies zulassen möchten. Bitte beachten Sie, dass bei einer Ablehnung womöglich nicht mehr alle Funktionalitäten der Seite zur Verfügung stehen.