- Beiträge: 8
- Dank erhalten: 0
Frage
Software will not open
- Rajivraj
-
Autor
- Offline
- Forum Nutzer
-
Weniger
Mehr
19 Jan 2017 06:00 #42744
von Rajivraj
Software will not open wurde erstellt von Rajivraj
Hello,
I have installed the UCCNC as stated in the YouTube videos following all the steps but when I plug the UC100 device in the USB board, the light is still solid green. I tried soluble clicking on the machine parameters for steocrsft 2/600 and no blue light as mentioned.
I also tried opening the UCCNC software, again no response..
Any suggestions
I have 32 bit windows vista with 2084mb of ram..
it's s dedicated laptop just for CNC..
I have installed the UCCNC as stated in the YouTube videos following all the steps but when I plug the UC100 device in the USB board, the light is still solid green. I tried soluble clicking on the machine parameters for steocrsft 2/600 and no blue light as mentioned.
I also tried opening the UCCNC software, again no response..
Any suggestions
I have 32 bit windows vista with 2084mb of ram..
it's s dedicated laptop just for CNC..
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- DerRoy
-
- Offline
- Forum Nutzer
-
Weniger
Mehr
- Beiträge: 356
- Dank erhalten: 149
19 Jan 2017 06:48 - 19 Jan 2017 06:48 #42746
von DerRoy
MfG
Roy
SC 600/2; SolidWorks;UCCnC und UC100; EstlCam und Arduino Steuerung; KRESS 800kfme;
DerRoy antwortete auf Software will not open
Hello Rajivraj,
Just to understand you correct:
When the UC100 is plugged in, but UCCNC is not started, you only have the green light on.
-》this is correct and normal. The blue light only goes on, once UCCNC is started and running.
You are not able to start UCCNC:
This is definitely not normal. I am not sure if this can help, but it's worth a try:
Did you try to run it as administrator?
Did you install it as administrator?
BR
Roy
Just to understand you correct:
When the UC100 is plugged in, but UCCNC is not started, you only have the green light on.
-》this is correct and normal. The blue light only goes on, once UCCNC is started and running.
You are not able to start UCCNC:
This is definitely not normal. I am not sure if this can help, but it's worth a try:
Did you try to run it as administrator?
Did you install it as administrator?
BR
Roy
MfG
Roy
SC 600/2; SolidWorks;
Letzte Änderung: 19 Jan 2017 06:48 von DerRoy.
Folgende Benutzer bedankten sich: Rajivraj
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- Rajivraj
-
Autor
- Offline
- Forum Nutzer
-
Weniger
Mehr
- Beiträge: 8
- Dank erhalten: 0
19 Jan 2017 08:13 #42752
von Rajivraj
Rajivraj antwortete auf Software will not open
The UCCNC is not running at all it's not even starting up when I click on it.
Yes I did install it as an administrator and also tried running it as an administrator. Still having the issue. It won't run UCCNC software..
Yes I did install it as an administrator and also tried running it as an administrator. Still having the issue. It won't run UCCNC software..
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- DocBrown
-
- Offline
- Forum Nutzer
-
19 Jan 2017 08:40 - 19 Jan 2017 08:40 #42754
von DocBrown
Viele Grüße
Hartmut
V2/420 China 800W wassergekühlt
UCCNC & ARDUINO ESTLCAM Controller
ESTLCAM & QCAD
DK5LH/G11
DocBrown antwortete auf Software will not open
...but you have installed the license key in the UCCNC directory and you don't have a fake UC100 interface which is sold sometimes on eBay and does not work...?
Anyway UCCNC must start even without a UC100. Then it starts in Demo mode...
Anyway UCCNC must start even without a UC100. Then it starts in Demo mode...
Viele Grüße
Hartmut
V2/420 China 800W wassergekühlt
UCCNC & ARDUINO ESTLCAM Controller
ESTLCAM & QCAD
DK5LH/G11
Letzte Änderung: 19 Jan 2017 08:40 von DocBrown.
Folgende Benutzer bedankten sich: Rajivraj
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- Rajivraj
-
Autor
- Offline
- Forum Nutzer
-
Weniger
Mehr
- Beiträge: 8
- Dank erhalten: 0
19 Jan 2017 08:45 #42755
von Rajivraj
Rajivraj antwortete auf Software will not open
I bought the step craft from stepcraft Australia. Was given the software in a USB stick with the license. It's all proper not from eBay or anywhere else. I bought the whole package with the HF spindle and UCCNC software package. Really dissappointrf right now. It's being already 2 days
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- Owen Sparks
-
- Offline
- Forum Nutzer
-
Weniger
Mehr
- Beiträge: 15
- Dank erhalten: 4
19 Jan 2017 09:04 - 19 Jan 2017 09:07 #42757
von Owen Sparks
Production Engineer
HWM-Water Ltd.
Owen Sparks antwortete auf Software will not open
Which version do you have?
Current version: 1.2029
available here:-
www.cncdrive.com/UCCNC.html
Owen S.
Current version: 1.2029
available here:-
www.cncdrive.com/UCCNC.html
Owen S.
Production Engineer
HWM-Water Ltd.
Letzte Änderung: 19 Jan 2017 09:07 von Owen Sparks.
Folgende Benutzer bedankten sich: Rajivraj
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- Rajivraj
-
Autor
- Offline
- Forum Nutzer
-
Weniger
Mehr
- Beiträge: 8
- Dank erhalten: 0
19 Jan 2017 09:11 #42758
von Rajivraj
Rajivraj antwortete auf Software will not open
The most current one which is 1.2029..
I reinstalled my windows on my laptop to make sure I had a clean computer just dedicated to CNC. I followed each as instructed, but after loading the software, clicking on it, it does nothing.. doesn't open at all.. ..
I reinstalled my windows on my laptop to make sure I had a clean computer just dedicated to CNC. I followed each as instructed, but after loading the software, clicking on it, it does nothing.. doesn't open at all.. ..
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- peterg1000
-
- Offline
- Forum Nutzer
-
Weniger
Mehr
- Beiträge: 380
- Dank erhalten: 131
19 Jan 2017 09:38 #42760
von peterg1000
SC 420/2, Industrial VFD spindle from StoneyCNC
UC100 + UCCNC
Cut2D, Autosketch10, Draftsight, Eagle 9.5.1
There is no problem, however simple, that cannot be made more complicated by thinking about it.
peterg1000 antwortete auf Software will not open
Hi,
Some things to try :-
Download another copy of UCCNC (rev 1.2029) from the cncdrive website and try that on your laptop.
If that doesn't work, have you another computer on which you can temporarily install the downloaded copy - you should be able to run this in demo mode if all is well with the download.
I noticed this on the cncdrive.com website relating to rev 1.2029
"Compatible OP systems: Windows XP, 7, 8, 8.1,10 on all both 32 and 64bit versions."
No mention of Vista - maybe a clue here!!!!
Peter
Some things to try :-
Download another copy of UCCNC (rev 1.2029) from the cncdrive website and try that on your laptop.
If that doesn't work, have you another computer on which you can temporarily install the downloaded copy - you should be able to run this in demo mode if all is well with the download.
I noticed this on the cncdrive.com website relating to rev 1.2029
"Compatible OP systems: Windows XP, 7, 8, 8.1,10 on all both 32 and 64bit versions."
No mention of Vista - maybe a clue here!!!!
Peter
SC 420/2, Industrial VFD spindle from StoneyCNC
UC100 + UCCNC
Cut2D, Autosketch10, Draftsight, Eagle 9.5.1
There is no problem, however simple, that cannot be made more complicated by thinking about it.
Folgende Benutzer bedankten sich: Rajivraj
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- DerRoy
-
- Offline
- Forum Nutzer
-
Weniger
Mehr
- Beiträge: 356
- Dank erhalten: 149
19 Jan 2017 12:12 #42778
von DerRoy
MfG
Roy
SC 600/2; SolidWorks;UCCnC und UC100; EstlCam und Arduino Steuerung; KRESS 800kfme;
DerRoy antwortete auf Software will not open
Just to mention, the software should also run without the licence file.
But it will be in demo mode in that case. But it should start.
Maybe Vista is the problem?
But it will be in demo mode in that case. But it should start.
Maybe Vista is the problem?
MfG
Roy
SC 600/2; SolidWorks;
Folgende Benutzer bedankten sich: Rajivraj
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- DocBrown
-
- Offline
- Forum Nutzer
-
19 Jan 2017 12:44 #42782
von DocBrown
Viele Grüße
Hartmut
V2/420 China 800W wassergekühlt
UCCNC & ARDUINO ESTLCAM Controller
ESTLCAM & QCAD
DK5LH/G11
DocBrown antwortete auf Software will not open
This forum ist just for UCCNC:
CNCDRIVE Forum
Maybe it's a good idea to ask there about the compatibility...
Maybe it's a good idea to ask there about the compatibility...
Viele Grüße
Hartmut
V2/420 China 800W wassergekühlt
UCCNC & ARDUINO ESTLCAM Controller
ESTLCAM & QCAD
DK5LH/G11
Folgende Benutzer bedankten sich: Rajivraj
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- ger21
-
- Offline
- Forum Nutzer
-
20 Jan 2017 00:17 #42817
von ger21
Gerry
UCCNC 2017 Screenset
www.thecncwoodworker.com/2017.html
ger21 antwortete auf Software will not open
Try installing the dot net fix from CNC Drive
cncdrive.com/MC/Software%20prerequirements/dotnetfx2_0.exe
cncdrive.com/MC/Software%20prerequirements/dotnetfx2_0.exe
Gerry
UCCNC 2017 Screenset
www.thecncwoodworker.com/2017.html
Folgende Benutzer bedankten sich: Rajivraj
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- peterg1000
-
- Offline
- Forum Nutzer
-
Weniger
Mehr
- Beiträge: 380
- Dank erhalten: 131
20 Jan 2017 10:07 #42822
von peterg1000
SC 420/2, Industrial VFD spindle from StoneyCNC
UC100 + UCCNC
Cut2D, Autosketch10, Draftsight, Eagle 9.5.1
There is no problem, however simple, that cannot be made more complicated by thinking about it.
peterg1000 antwortete auf Software will not open
Hi
I think that link refers to the version for Win XP.
The Microsoft website suggests rev 3.5 for Vista, I don't know if the .NET framework loads automatically in Vista
Here is a link to the update for you to explore - a fresh installation might just sort the problem.
Peter.
I think that link refers to the version for Win XP.
The Microsoft website suggests rev 3.5 for Vista, I don't know if the .NET framework loads automatically in Vista
Here is a link to the update for you to explore - a fresh installation might just sort the problem.
Peter.
SC 420/2, Industrial VFD spindle from StoneyCNC
UC100 + UCCNC
Cut2D, Autosketch10, Draftsight, Eagle 9.5.1
There is no problem, however simple, that cannot be made more complicated by thinking about it.
Folgende Benutzer bedankten sich: Rajivraj
Bitte Anmelden oder Registrieren um der Konversation beizutreten.
- Rajivraj
-
Autor
- Offline
- Forum Nutzer
-
Weniger
Mehr
- Beiträge: 8
- Dank erhalten: 0
20 Jan 2017 23:25 #42883
von Rajivraj
Thanks Everyone for all your all help. The issue was with windows Vista. Once i installed windows 7. Everything works fine.
So glad it all works
Rajivraj antwortete auf Software will not open
Thanks Everyone for all your all help. The issue was with windows Vista. Once i installed windows 7. Everything works fine.So glad it all works
Bitte Anmelden oder Registrieren um der Konversation beizutreten.