Please Log in or Create an account to join the conversation.
spur0 wrote:
Ich denke, dass man erst eine plangefräste Grundplatte braucht, auch wenn sie zu dem Zeitpunkt noch kleine Erhöhungen hat.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
spur0 wrote: ... aber wenn die Spindel leicht schräg steht und ich plane, bekomme ich so eine Oberfläche (leicht übertrieben), je nach Überlappung mehr oder weniger, da die Fräserunterseite ja auch nicht waagrecht ist sondern leicht schräg:
Please Log in or Create an account to join the conversation.
spur0 wrote: ...aber wenn die Spindel leicht schräg steht und ich plane, bekomme ich so eine Oberfläche (leicht übertrieben), je nach Überlappung mehr oder weniger, da die Fräserunterseite ja auch nicht waagrecht ist sondern leicht schräg:
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Ich hatte Dich so verstanden das Du den gesamten Arbeitsbereich 2x planen wolltest. Deshalb meine Abwandlung deines Grundgedankens mit einer kleineren Platte bevor es eben an die große geht ...spur0 wrote: @Worldhusky:
das war ja mein Grundgedanke, erst eine Platte planen und dann mittels Haarlineal die Senkrechte zu vermessen, wenn dies geschehen ist, die Platte nochmals planen. Die Parallelität der Platte zur X-Achse passt ja sowieso wenn man plant, ebenso zur Y-Achse. Einzig die Spindel bzw. Proxxon könnte leicht schräg stehen.
Steht "sch..." für "schön" ... ?spur0 wrote: Also meine geschlichteten Flächen sehen derzeit sch... aus, deswegen auch der Thread.
Please Log in or Create an account to join the conversation.
Worldhusky wrote:
Hat irgendjemand eine Maßstabsgetreue Zeichnung (2D dxf/dwg) von der Spindelaufnahme oder weiß wo man die im www findet?
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Weil ich mir schon einen Namen als grober Spielverderber gemacht habe, hier die, nach dem Originalteil der Spindelaufnahme, erstellte Zeichung von mir:Worldhusky wrote: Hat irgendjemand eine Maßstabsgetreue Zeichnung (2D dxf/dwg) von der Spindelaufnahme oder weiß wo man die im www findet?
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
sswjs wrote: ... hier die, nach dem Originalteil der Spindelaufnahme, erstellte Zeichung von mir:
Jetzt kann sie jeder ändern, wie er will.
sswjs, aka Jens
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Welche willst du denn haben?Worldhusky wrote: Kannst Du mir noch die Materialstärke nennen? (Ja, ich weiß - ich bin unersättlich!)
Please Log in or Create an account to join the conversation.
sswjs wrote: ... an dem Teil kann man von 9,8 bis 10,2 mm alles messen, was man will.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
We use cookies on our website. Some of them are essential for the operation of the site, while others help us to improve this site and the user experience (tracking cookies). You can decide for yourself whether you want to allow cookies or not. Please note that if you reject them, you may not be able to use all the functionalities of the site.