Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Ich geb mal die provokante Antwort: Es sollte nicht normal sein.ManuelK wrote: Ist dies normal so?
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Ich installiere auch schon lange nicht mehr jedes Update, was auf den Markt geschmissen wird.Ich alter Fuchs halt mich an das "nerver change a running systems"
Auch das trifft bei mir nicht zu, denn ich habe eine 420er.Das mit der Z-Achse hat Burkard doch schon erklärt mit den Schritten was von der 3mm Steigung der Spindel herkommt.
Please Log in or Create an account to join the conversation.
Jokel wrote: Das mit der Z-Achse hat Burkard doch schon erklärt mit den Schritten was von der 3mm Steigung der Spindel herkommt. Bei Schrittmotoren gibt es nunmal nur ganze Schritte und das ist bei Euch dieser Wert 0,0375.
Evtl ist das ja nur ein Fehler in der Grafischen Anzeige und der Wert stimmt doch. Hat das schon einer mit ner Micrometer nachgemessen?
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
spur0 wrote: Stimmt,
wir sind im 1/1000 Bereich, bei der 420er also 0,005mm und das kann WinPC sowieso nicht anzeigen, ...
Please Log in or Create an account to join the conversation.
Kontrollmessungen nach Beendigung des Fräsjobs haben bisher immer ergeben, dass die im Kommunikationsfenster angezeigte Tiefe auch genau erreicht wurde, je nach Genauigkeit des Messmittels bis auf 5 Hundertstel genau.
Auch wenn die SC eine bedingte Ungenauigkeit mit sich bringt, so summieren sich die Werte irgendwo und man befindet sich dann bald im 1/10-Bereich. Das mag bei Sperrholz egal sein, aber wenn es mal wirklich passen soll ist das undiskutabel.Also ruhig bleiben und die Differenzen, so es denn welche sein sollten, ignorieren.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Alpenkreuzer wrote:
Wichtig für mich ist nur das "Kommunikationsmodul" (Lesart Handbuch Lewetz), in dem die erreichten Koordinaten (nicht die anzufahrenden) angezeigt werden - auch da wieder nur interessant die Z-Werte.
Please Log in or Create an account to join the conversation.
spur0 wrote:
Alpenkreuzer wrote:
Wichtig für mich ist nur das "Kommunikationsmodul" (Lesart Handbuch Lewetz), in dem die erreichten Koordinaten (nicht die anzufahrenden) angezeigt werden - auch da wieder nur interessant die Z-Werte.
Hallo Michael,
und genau in deinem "Kommunikationsmodul" sind sie falsch, in dem einen Fall bei mir über 1/10, das kann ich nicht ignorieren, sorry
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
spur0 wrote: Sieh dir mal die Bilder in meinem ersten Post an, da siehst du die Unterschiede zwischen soll und ist, das angezeigte "ist" ist auch das was gefräst wird, also falsch ...
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
spur0 wrote: Sieh dir mal Bild 1 an, da besagt die linke Seite (Echtzeitfenster) dass Z= 1,0800 sein soll, die blaue Markierung darunter dass er schon 2 Steps weiter ist, sprich in dieser Tiefe arbeitet.
Auf der rechten Seite siehst du den IST Zustand den WinPC an die Maschine abgibt, eben dein Kommunikationsfenster. Hier ist die Tiefe allerdings nur 0,965, also 0,115mm zu hoch.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Alpenkreuzer wrote: - das K.-Fenster zeigt aber als tatsächlich erreichte Tiefe ...
...DU HAST RECHT! Gebe mich geschlagen.
Please Log in or Create an account to join the conversation.
We use cookies on our website. Some of them are essential for the operation of the site, while others help us to improve this site and the user experience (tracking cookies). You can decide for yourself whether you want to allow cookies or not. Please note that if you reject them, you may not be able to use all the functionalities of the site.