question-circle Question layering issue in 3D printing

  • Annie
  • Annie's Avatar Topic Author
  • Offline
  • Forum Nutzer
  • Forum Nutzer
More
13 May 2016 13:36 #34115 by Annie
layering issue in 3D printing was created by Annie
Hello there,
I've just started using my machine, SC2-420 but I found one issue with layering which doesn't make second and the following layers in the same point like the picture attached. I checked the machine several times if there's jammming with X, Y and Z axes but I think I solved the problem after re-leveling. Can you tell me what to do?
Thanks.

Annie

This message has an attachment image.
Please log in or register to see it.

Please Log in or Create an account to join the conversation.

More
13 May 2016 16:30 #34119 by Rexfreund
Replied by Rexfreund on topic layering issue in 3D printing
Hello,

can you place your gcode and/or your STL file here.

I think we can found your Problem easier.

Klaus

Heli, Hexakopter,....
WinPC-NC USB, Eigenbau Fräserl mit Mechapro Interface II, Kress FME 1050, Filou.
Zum Zeichen, Fusion 360 ! mit Hobbylizenz. macht Laune ;-)
3D-Drucker (Mankati Basis) Dualprint 2x E3D-V6 2x Bondtech Bowdenextruder Simplify3D (SC-Druckkopf)
The following user(s) said Thank You: Annie

Please Log in or Create an account to join the conversation.

  • Annie
  • Annie's Avatar Topic Author
  • Offline
  • Forum Nutzer
  • Forum Nutzer
More
13 May 2016 18:24 #34123 by Annie
Replied by Annie on topic layering issue in 3D printing
Thank you for your response and here we go~. Actually this gcode file is in the CD provided when I bought my machine though...

Please Log in or Create an account to join the conversation.

More
14 May 2016 09:33 #34134 by Rexfreund
Replied by Rexfreund on topic layering issue in 3D printing
hello,
I'm sorry but i dont have a stepcraft either the Printhead in use.
I can only remember me that on the CD there are stl files and no gcode file.
The Gcode was created from the slicer and controlls your cnc router over the Win-PCNC or any other controling Software. I dont know what ever you use.
This Gcode file shows what the slicer has made from the 3D-stl file. Read this file and you can locate which component doesn't work correct. If this file OK, then the guilty component is the controling software.

Greetings from Bavaria
Klaus

Heli, Hexakopter,....
WinPC-NC USB, Eigenbau Fräserl mit Mechapro Interface II, Kress FME 1050, Filou.
Zum Zeichen, Fusion 360 ! mit Hobbylizenz. macht Laune ;-)
3D-Drucker (Mankati Basis) Dualprint 2x E3D-V6 2x Bondtech Bowdenextruder Simplify3D (SC-Druckkopf)
The following user(s) said Thank You: Annie

Please Log in or Create an account to join the conversation.

  • Annie
  • Annie's Avatar Topic Author
  • Offline
  • Forum Nutzer
  • Forum Nutzer
More
19 May 2016 21:37 #34271 by Annie
Replied by Annie on topic layering issue in 3D printing
Thank you for your attention and response. I finally printed out with the original file I tried and found the problem was leveling. I put a fabric under the machine and it worked well with a little bit of its resistance not to make my SC2 shake too much.

Please Log in or Create an account to join the conversation.

More
05 Dec 2016 20:19 #40167 by bernardp
Replied by bernardp on topic layering issue in 3D printing
Hello Annie, sorry but your problem interest me.
Is it resolved? What's your speed setting to print perimeter or infill?
In my case, I can't work up to 15mm/s without stalling of my X Y axis.
Thanks,
Philippe

Please Log in or Create an account to join the conversation.

Powered by Kunena Forum

© 2019 STEPCRAFT GmbH & Co. KG