- Posts: 3
- Thank you received: 0
Question
UCCNC Software Wont Reset
- murrayec
-
Topic Author
- Offline
- Forum Nutzer
-
Less
More
07 Feb 2016 17:04 #30338
by murrayec
UCCNC Software Wont Reset was created by murrayec
Hi
I need some help please;-
Windows 7
420 machine
Just set up a new machine and installed the UC100 and UCCNC software, when the software starts it will not allow the reset to be reset- it reports an e-stop button or limit switch is causing a problem! I have checked all of these and are working OK! In the diagnostics menu 'Hard Limits' & 'Reset' are highlighted!
Can anyone help
Thanks
Eoin
I need some help please;-
Windows 7
420 machine
Just set up a new machine and installed the UC100 and UCCNC software, when the software starts it will not allow the reset to be reset- it reports an e-stop button or limit switch is causing a problem! I have checked all of these and are working OK! In the diagnostics menu 'Hard Limits' & 'Reset' are highlighted!
Can anyone help
Thanks
Eoin
Please Log in or Create an account to join the conversation.
- mikath
-
- Offline
- Forum Nutzer
-
- SV&LV
07 Feb 2016 20:51 #30354
by mikath
Stepcraft M.1000 + HIWIN Ball Screw + Semi-Closed Loop System + MM-1000 DI + Automatic Tool Changer + 2 Rows Tool Magazine Pneumatic Lifting + Engraving Laser DL445 + 4th Axis + Aluminum T-slot table + 3D Touch Probe + UCR201 + UCCNC + VCarve Pro + Cut3D + CorelDraw 2018 + Autodesk Inventor
Replied by mikath on topic UCCNC Software Wont Reset
Do you have the right profile?
Can´t you "Overide Limits" and move away from the ends?
/Mika
Can´t you "Overide Limits" and move away from the ends?
/Mika
Stepcraft M.1000 + HIWIN Ball Screw + Semi-Closed Loop System + MM-1000 DI + Automatic Tool Changer + 2 Rows Tool Magazine Pneumatic Lifting + Engraving Laser DL445 + 4th Axis + Aluminum T-slot table + 3D Touch Probe + UCR201 + UCCNC + VCarve Pro + Cut3D + CorelDraw 2018 + Autodesk Inventor
Please Log in or Create an account to join the conversation.
- murrayec
-
Topic Author
- Offline
- Forum Nutzer
-
Less
More
- Posts: 3
- Thank you received: 0
07 Feb 2016 23:36 #30363
by murrayec
Replied by murrayec on topic UCCNC Software Wont Reset
Hi Mika
Yes I have the 420 profile installed that came with the software.
I can click on 'Overide Limits' but the 'Reset' button is still flashing and wont reset! Also I notice the blue LED on the UC100 does not come on!
Thanks for reply
Eoin
Yes I have the 420 profile installed that came with the software.
I can click on 'Overide Limits' but the 'Reset' button is still flashing and wont reset! Also I notice the blue LED on the UC100 does not come on!
Thanks for reply
Eoin
Please Log in or Create an account to join the conversation.
- Rory
-
- Offline
- Forum Nutzer
-
Less
More
- Posts: 383
- Thank you received: 147
08 Feb 2016 09:22 - 08 Feb 2016 09:22 #30369
by Rory
Replied by Rory on topic UCCNC Software Wont Reset
If there is no blue light then the USB module has not been recognised. check top of UCCNC screen. Top left hand corner it will say "UCCNC running in demo mode"
See here
See here
Last edit: 08 Feb 2016 09:22 by Rory.
Please Log in or Create an account to join the conversation.
- murrayec
-
Topic Author
- Offline
- Forum Nutzer
-
Less
More
- Posts: 3
- Thank you received: 0
08 Feb 2016 13:04 #30376
by murrayec
All sorted this morning with the help of Rory, a little update from the installed software on the hard drive and its up and running
Thanks
Eoin
Replied by murrayec on topic UCCNC Software Wont Reset
Rory wrote: If there is no blue light then the USB module has not been recognised. check top of UCCNC screen. Top left hand corner it will say "UCCNC running in demo mode"
See here
All sorted this morning with the help of Rory, a little update from the installed software on the hard drive and its up and running
Thanks
Eoin
Please Log in or Create an account to join the conversation.