- Posts: 93
- Thank you received: 105
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
bvps wrote: Offtopic, muss aber sein:
Der Realtime-Service von Christian ist sensationell. Danke
Bernd
Please Log in or Create an account to join the conversation.
bvps wrote: Offtopic, muss aber sein:
Der Realtime-Service von Christian ist sensationell. Danke
Bernd
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Worldhusky wrote: Würde es nicht mehr Sinn machen - im puncto konsequenterer workflow - eine 3D Zeichnung (in .stl) an Estlcam zu übergeben?
Gibt es irgendwas - was ich nicht bedacht habe - was dem entgegensteht?
Please Log in or Create an account to join the conversation.
Das war mir so noch nicht bewusst gewesen - danke fürs "Aufklären".Christian Knüll wrote: 3D dauert ein mehrfaches länger zu fräsen, da das Modell einfach "stupide" in X, Y oder Z Richtung Zeile für Zeile bzw. Ebene für Ebene abgezeilt wird.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
sumstefan wrote: Hallo Wolfgang,
das Teil sollte doch so aussehen
In EstlCAM mußt du zuerst das Was als Insel Stehen bleiben soll alls "Teil" definieren 0mm Tiefe
Dann den Ausschnitt in der Insel als Ausschnitt 2,5mm Tiefe.
Dann das Große Teil als Ausschnitt, dann auf Insel klicken und die Anleitung genau befolgen.
Gruß
Stefan
Was soll als "Teil" definiert werden, die Nut mit 2,5mm oder die Flsche die stehen bleiben soll, beides soll ja von dem äußeren Ausschnitt nicht berücksichtigt werden?In EstlCAM mußt du zuerst das Was als Insel Stehen bleiben soll als "Teil" definieren 0mm Tiefe
Meinst du jetzt die Nut oder das Äußere? Ich hätte die Nut 2,5mm und die Fläche mit 1,5mm angeben sollen, wäre einfacher zum Verständnis.Dann den Ausschnitt in der Insel als Ausschnitt 2,5mm Tiefe.
Das der "große" Teil das letzte ist ist mir klar, aber was soll ich befolgen?Dann das Große Teil als Ausschnitt, dann auf Insel klicken und die Anleitung genau befolgen.
Please Log in or Create an account to join the conversation.
spur0 wrote: In meinem Fall kann ich das Objekt aber nicht erstellen oder gibt es die Möglichkeit die Frästiefe mit 0mm anzugeben
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Logisch, ich wollt's halt vereinfachen...spur0 wrote: @Jens:
das passt nicht ganz mit dem überein was ich brauche
Ok, da du meinen bildlichen Anweisungen auch nicht so richtig folgen kannst, hier noch mal als Text:spur0 wrote: Was mir aber aufgefallen ist, ich definiere die Nut gleich als Tasche, anscheinend ist das schon mal ein Fehler, macht das Estlcam nach der Insel von alleine?
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
Please Log in or Create an account to join the conversation.
We use cookies on our website. Some of them are essential for the operation of the site, while others help us to improve this site and the user experience (tracking cookies). You can decide for yourself whether you want to allow cookies or not. Please note that if you reject them, you may not be able to use all the functionalities of the site.